104 lines
2.0 KiB
INI
104 lines
2.0 KiB
INI
[mcu sht]
|
|
canbus_uuid: 8ce295109ef0
|
|
|
|
[firmware_retraction]
|
|
retract_length: 0.4
|
|
retract_speed: 30
|
|
unretract_speed: 30
|
|
|
|
[adxl345]
|
|
cs_pin: sht:PA9
|
|
spi_bus: spi2
|
|
#axes_map: z,-y,x
|
|
|
|
[resonance_tester]
|
|
probe_points: 177.5, 177.5, 50
|
|
accel_chip: adxl345
|
|
min_freq: 15
|
|
max_freq: 120
|
|
accel_per_hz: 125
|
|
hz_per_sec: 1
|
|
|
|
[input_shaper]
|
|
shaper_type_x: mzv
|
|
shaper_freq_x: 51
|
|
shaper_type_y: mzv
|
|
shaper_freq_y: 41.6
|
|
|
|
[temperature_sensor sht36_v2]
|
|
sensor_type: temperature_mcu
|
|
sensor_mcu: sht
|
|
|
|
|
|
|
|
#####################################################################
|
|
# Extruder
|
|
#####################################################################
|
|
|
|
[extruder]
|
|
step_pin: sht:PB4
|
|
dir_pin: sht:PB3
|
|
enable_pin: !sht:PA15
|
|
microsteps: 16
|
|
rotation_distance: 53.494165
|
|
gear_ratio: 44:10, 37:17
|
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: sht:PA8
|
|
sensor_type: PT1000
|
|
sensor_pin: sht:PA3
|
|
pullup_resistor: 1100
|
|
min_temp: 20
|
|
max_temp: 350
|
|
max_power: 1.0
|
|
max_extrude_only_distance: 300
|
|
max_extrude_cross_section: 5
|
|
min_extrude_temp: 20
|
|
control: pid
|
|
pid_Kp: 26.171
|
|
pid_Ki: 2.684
|
|
pid_Kd: 63.793
|
|
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: sht:PB5
|
|
#diag_pin: sht:PB6
|
|
interpolate: false
|
|
run_current: 0.65 #0.6
|
|
#sense_resistor: 0.110
|
|
#stealthchop_threshold: 0 # 999999
|
|
|
|
[autotune_tmc extruder]
|
|
motor: ldo-36sth20-1004ahg
|
|
|
|
#####################################################################
|
|
# Probe
|
|
#####################################################################
|
|
|
|
[probe]
|
|
pin: ^!sht:PA2
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
[fan]
|
|
#hardware_pwm: True
|
|
#kick_start_time: 0.25
|
|
#cycle_time: 0.15
|
|
off_below: 0.05
|
|
pin: sht:PB11
|
|
|
|
[heater_fan hotend_fan]
|
|
pin: sht:PB10
|
|
heater: extruder
|
|
|
|
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
[neopixel sb_leds]
|
|
pin: sht:PB0 |