Mikhail Shahovalov
715bcc0506
Klipper version: v0.13.0-403-gb4c7cf4a Moonraker version: v0.9.3-125-g3129d89 Mainsail version: v2.14.0
174 lines
4.4 KiB
INI
174 lines
4.4 KiB
INI
# SB RapidoV2 G2E
|
||
|
||
[include rapido_v2.cfg]
|
||
|
||
[mcu EBBCan]
|
||
canbus_uuid: d7e70bd38059
|
||
|
||
[firmware_retraction]
|
||
retract_length: 0.3
|
||
# The length of filament (in mm) to retract when G10 is activated,
|
||
# and to unretract when G11 is activated (but see
|
||
# unretract_extra_length below). The default is 0 mm.
|
||
retract_speed: 35
|
||
# The speed of retraction, in mm/s. The default is 20 mm/s.
|
||
#unretract_extra_length: 0
|
||
# The length (in mm) of *additional* filament to add when
|
||
# unretracting.
|
||
unretract_speed: 35
|
||
# The speed of unretraction, in mm/s. The default is 10 mm/s.
|
||
|
||
[adxl345]
|
||
cs_pin: EBBCan:gpio1
|
||
spi_software_sclk_pin: EBBCan:gpio2
|
||
spi_software_mosi_pin: EBBCan:gpio0
|
||
spi_software_miso_pin: EBBCan:gpio3
|
||
axes_map: z,-y,x
|
||
|
||
[resonance_tester]
|
||
probe_points: 177.5, 177.5, 50
|
||
accel_chip: adxl345
|
||
min_freq: 15
|
||
max_freq: 120
|
||
accel_per_hz: 125
|
||
hz_per_sec: 1
|
||
|
||
[input_shaper]
|
||
#max 4000
|
||
shaper_type_x:mzv
|
||
shaper_freq_x:53.400
|
||
shaper_type_y:mzv
|
||
shaper_freq_y:42.200
|
||
|
||
[temperature_sensor SB2209]
|
||
sensor_type: temperature_mcu
|
||
sensor_mcu: EBBCan
|
||
|
||
[temperature_sensor Ebb]
|
||
sensor_type: Generic 3950
|
||
sensor_pin: EBBCan:gpio28
|
||
|
||
|
||
#####################################################################
|
||
# Extruder
|
||
#####################################################################
|
||
|
||
[extruder]
|
||
step_pin: EBBCan:gpio18
|
||
dir_pin: EBBCan:gpio19
|
||
enable_pin: !EBBCan:gpio17
|
||
microsteps: 16
|
||
rotation_distance: 46.64 #G2E
|
||
gear_ratio: 9:1 #G2E
|
||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||
nozzle_diameter: 0.400
|
||
filament_diameter: 1.750
|
||
heater_pin: EBBCan:gpio7
|
||
|
||
#sensor_type: ATC Semitec 104NT-4-R025H42G
|
||
#sensor_pin: EBBCan:gpio27
|
||
|
||
#sensor_type: PT1000
|
||
#sensor_pin: EBBCan:gpio27
|
||
|
||
#pullup_resistor: 1000
|
||
|
||
sensor_type: MAX31865
|
||
sensor_pin: EBBCan:gpio9
|
||
spi_software_sclk_pin: EBBCan:gpio10
|
||
spi_software_mosi_pin: EBBCan:gpio8
|
||
spi_software_miso_pin: EBBCan:gpio11
|
||
rtd_nominal_r: 1000
|
||
rtd_reference_r: 4300
|
||
rtd_num_of_wires: 2
|
||
|
||
min_temp: 20
|
||
max_temp: 350
|
||
max_power: 1.0
|
||
max_extrude_only_distance: 300
|
||
max_extrude_cross_section: 5
|
||
min_extrude_temp: 20
|
||
|
||
control: pid
|
||
pid_Kp: 26.171
|
||
pid_Ki: 2.684
|
||
pid_Kd: 63.793
|
||
|
||
|
||
|
||
[tmc2209 extruder]
|
||
uart_pin: EBBCan:gpio20
|
||
interpolate: false
|
||
run_current: 0.65 #0.6
|
||
#sense_resistor: 0.110
|
||
#stealthchop_threshold: 0 # 999999
|
||
|
||
[autotune_tmc extruder]
|
||
motor: ldo-36sth20-1004ahg-9T
|
||
|
||
|
||
|
||
[filament_switch_sensor G2E]
|
||
pause_on_runout: True
|
||
runout_gcode:
|
||
UNLOAD_FILAMENT
|
||
insert_gcode:
|
||
LOAD_FILAMENT
|
||
switch_pin: ^EBBCan:gpio24
|
||
|
||
|
||
#####################################################################
|
||
# Probe
|
||
#####################################################################
|
||
|
||
[probe]
|
||
pin: ^!EBBCan:gpio21
|
||
|
||
#####################################################################
|
||
# Fan Control
|
||
#####################################################################
|
||
|
||
[fan]
|
||
#hardware_pwm: False
|
||
#pin: EBBCan:gpio13 #gpio15
|
||
#off_below: 0.05
|
||
#cycle_time: 0.00008
|
||
|
||
# Время (в секундах), необходимое для запуска вентилятора на полной скорости при первом включении
|
||
# или увеличении ее более чем на 50% (помогает запустить вентилятор). Значение по умолчанию равно 0,100 секунды.
|
||
#kick_start_time: 0.150
|
||
# Время (в секундах), затрачиваемое на каждый цикл подачи питания на вентилятор с помощью ШИМ.
|
||
# Рекомендуется, чтобы это значение составляло 10 миллисекунд или более при использовании программного управления ШИМ.
|
||
# Значение по умолчанию равно 0,010 секунды.
|
||
#cycle_time: 0.01
|
||
#tachometer_pin: EBBCan:gpio12
|
||
#tachometer_poll_interval: 0.0005 #0.0005
|
||
#tachometer_ppr: 1
|
||
|
||
[heater_fan hotend_fan]
|
||
## Hotend Fan - CNC_FAN1
|
||
pin: EBBCan:gpio14
|
||
#max_power: 1.0
|
||
#kick_start_time: 0.5
|
||
heater: extruder
|
||
## If you are experiencing back flow, you can reduce fan_speed
|
||
#fan_speed: 1.0
|
||
|
||
#[temperature_fan EbbFan]
|
||
#pin: EBBCan:gpio6
|
||
#max_power: 1.0
|
||
#shutdown_speed: 0.0
|
||
#sensor_type: Generic 3950
|
||
#sensor_pin: EBBCan:gpio28
|
||
#min_temp: 0
|
||
#max_temp: 100
|
||
#target_temp: 60.0
|
||
#control: watermark
|
||
|
||
|
||
#####################################################################
|
||
# LED Control
|
||
#####################################################################
|
||
|
||
[neopixel sb_leds]
|
||
pin: EBBCan:gpio16 |