Autocommit from 2025-08-18 08:29:51

Klipper version: v0.13.0-154-g9346ad19

Moonraker version: v0.9.3-77-gccbfd64

Mainsail version: v2.14.0

firmware/boot_rp_sb2209.can

@@ -0,0 +1,54 @@
+CONFIG_LOW_LEVEL_OPTIONS=y
+# CONFIG_MACH_LPC176X is not set
+# CONFIG_MACH_STM32 is not set
+CONFIG_MACH_RPXXXX=y
+CONFIG_BOARD_DIRECTORY="rp2040"
+CONFIG_MCU="rp2040"
+CONFIG_CLOCK_FREQ=12000000
+CONFIG_FLASH_SIZE=0x200000
+CONFIG_FLASH_BOOT_ADDRESS=0x10000100
+CONFIG_RAM_START=0x20000000
+CONFIG_RAM_SIZE=0x42000
+CONFIG_STACK_SIZE=512
+CONFIG_FLASH_APPLICATION_ADDRESS=0x10004000
+CONFIG_FLASH_START=0x10000000
+CONFIG_LAUNCH_APP_ADDRESS=0x10004000
+CONFIG_BLOCK_SIZE=64
+CONFIG_RPXXXX_SELECT=y
+CONFIG_MACH_RP2040=y
+# CONFIG_MACH_RP2350 is not set
+CONFIG_RP2040_HAVE_STAGE2=y
+# CONFIG_RP2040_FLASH_W25Q080 is not set
+CONFIG_RP2040_FLASH_GENERIC_03=y
+CONFIG_RP2040_STAGE2_FILE="boot2_generic_03h.S"
+CONFIG_RP2040_STAGE2_CLKDIV=4
+# CONFIG_RPXXXX_FLASH_START_0100 is not set
+CONFIG_RPXXXX_FLASH_START_4000=y
+# CONFIG_RPXXXX_USB is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_0_1 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_12_13 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_16_17 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_28_29 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_4_5 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_8_9 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_20_21 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_24_25 is not set
+CONFIG_RPXXXX_CANBUS=y
+# CONFIG_RPXXXX_USBCANBUS is not set
+CONFIG_RPXXXX_CANBUS_GPIO_RX=4
+CONFIG_RPXXXX_CANBUS_GPIO_TX=5
+CONFIG_USB_VENDOR_ID=0x1d50
+CONFIG_USB_DEVICE_ID=0x6177
+CONFIG_USB_SERIAL_NUMBER="12345"
+CONFIG_CANSERIAL=y
+CONFIG_CANBUS=y
+CONFIG_CANBUS_FREQUENCY=1000000
+CONFIG_CANBUS_FILTER=y
+CONFIG_INITIAL_PINS=""
+CONFIG_ENABLE_DOUBLE_RESET=y
+# CONFIG_ENABLE_BUTTON is not set
+CONFIG_ENABLE_LED=y
+CONFIG_STATUS_LED_PIN="gpio26"
+CONFIG_BUILD_DEPLOYER=y
+CONFIG_HAVE_CHIPID=y
+CONFIG_KATAPULT_VERSION="v0.0.1-96-gbc1ecea"

firmware/boot_rp_sb2209.can.old

@@ -0,0 +1,53 @@
+CONFIG_LOW_LEVEL_OPTIONS=y
+# CONFIG_MACH_LPC176X is not set
+# CONFIG_MACH_STM32 is not set
+CONFIG_MACH_RPXXXX=y
+CONFIG_BOARD_DIRECTORY="rp2040"
+CONFIG_MCU="rp2040"
+CONFIG_CLOCK_FREQ=12000000
+CONFIG_FLASH_SIZE=0x200000
+CONFIG_FLASH_BOOT_ADDRESS=0x10000100
+CONFIG_RAM_START=0x20000000
+CONFIG_RAM_SIZE=0x42000
+CONFIG_STACK_SIZE=512
+CONFIG_FLASH_APPLICATION_ADDRESS=0x10000100
+CONFIG_FLASH_START=0x10000000
+CONFIG_LAUNCH_APP_ADDRESS=0x10004000
+CONFIG_BLOCK_SIZE=64
+CONFIG_RPXXXX_SELECT=y
+CONFIG_MACH_RP2040=y
+# CONFIG_MACH_RP2350 is not set
+CONFIG_RP2040_HAVE_STAGE2=y
+# CONFIG_RP2040_FLASH_W25Q080 is not set
+CONFIG_RP2040_FLASH_GENERIC_03=y
+CONFIG_RP2040_STAGE2_FILE="boot2_generic_03h.S"
+CONFIG_RP2040_STAGE2_CLKDIV=4
+CONFIG_RPXXXX_FLASH_START_0100=y
+# CONFIG_RPXXXX_FLASH_START_4000 is not set
+# CONFIG_RPXXXX_USB is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_0_1 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_12_13 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_16_17 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_28_29 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_4_5 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_8_9 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_20_21 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_24_25 is not set
+CONFIG_RPXXXX_CANBUS=y
+# CONFIG_RPXXXX_USBCANBUS is not set
+CONFIG_RPXXXX_CANBUS_GPIO_RX=4
+CONFIG_RPXXXX_CANBUS_GPIO_TX=5
+CONFIG_USB_VENDOR_ID=0x1d50
+CONFIG_USB_DEVICE_ID=0x6177
+CONFIG_USB_SERIAL_NUMBER="12345"
+CONFIG_CANSERIAL=y
+CONFIG_CANBUS=y
+CONFIG_CANBUS_FREQUENCY=1000000
+CONFIG_CANBUS_FILTER=y
+CONFIG_INITIAL_PINS=""
+CONFIG_ENABLE_DOUBLE_RESET=y
+# CONFIG_ENABLE_BUTTON is not set
+CONFIG_ENABLE_LED=y
+CONFIG_STATUS_LED_PIN="gpio26"
+CONFIG_HAVE_CHIPID=y
+CONFIG_KATAPULT_VERSION="v0.0.1-96-gbc1ecea"

firmware/ebb_rp2240.CAN

@@ -0,0 +1,86 @@
+CONFIG_LOW_LEVEL_OPTIONS=y
+# CONFIG_MACH_AVR is not set
+# CONFIG_MACH_ATSAM is not set
+# CONFIG_MACH_ATSAMD is not set
+# CONFIG_MACH_LPC176X is not set
+# CONFIG_MACH_STM32 is not set
+# CONFIG_MACH_HC32F460 is not set
+CONFIG_MACH_RPXXXX=y
+# CONFIG_MACH_PRU is not set
+# CONFIG_MACH_AR100 is not set
+# CONFIG_MACH_LINUX is not set
+# CONFIG_MACH_SIMU is not set
+CONFIG_BOARD_DIRECTORY="rp2040"
+CONFIG_MCU="rp2040"
+CONFIG_CLOCK_FREQ=12000000
+CONFIG_FLASH_SIZE=0x200000
+CONFIG_FLASH_BOOT_ADDRESS=0x10000100
+CONFIG_RAM_START=0x20000000
+CONFIG_RAM_SIZE=0x42000
+CONFIG_STACK_SIZE=512
+CONFIG_FLASH_APPLICATION_ADDRESS=0x10004000
+CONFIG_RPXXXX_SELECT=y
+CONFIG_MACH_RP2040=y
+# CONFIG_MACH_RP2350 is not set
+CONFIG_RPXXXX_HAVE_BOOTLOADER=y
+# CONFIG_RPXXXX_FLASH_START_0100 is not set
+CONFIG_RPXXXX_FLASH_START_4000=y
+CONFIG_RP2040_STAGE2_FILE="boot2_w25q080.S"
+CONFIG_RP2040_STAGE2_CLKDIV=2
+# CONFIG_RPXXXX_USB is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_0_1 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_12_13 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_16_17 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_28_29 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_4_5 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_8_9 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_20_21 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_24_25 is not set
+CONFIG_RPXXXX_CANBUS=y
+# CONFIG_RPXXXX_USBCANBUS is not set
+CONFIG_RPXXXX_CANBUS_GPIO_RX=4
+CONFIG_RPXXXX_CANBUS_GPIO_TX=5
+CONFIG_USB_VENDOR_ID=0x1d50
+CONFIG_USB_DEVICE_ID=0x614e
+CONFIG_USB_SERIAL_NUMBER="12345"
+CONFIG_WANT_ADC=y
+CONFIG_WANT_SPI=y
+CONFIG_WANT_SOFTWARE_SPI=y
+CONFIG_WANT_I2C=y
+CONFIG_WANT_SOFTWARE_I2C=y
+CONFIG_WANT_HARD_PWM=y
+CONFIG_WANT_BUTTONS=y
+CONFIG_WANT_TMCUART=y
+CONFIG_WANT_NEOPIXEL=y
+CONFIG_WANT_PULSE_COUNTER=y
+CONFIG_WANT_ST7920=y
+CONFIG_WANT_HD44780=y
+CONFIG_WANT_ADXL345=y
+CONFIG_WANT_LIS2DW=y
+CONFIG_WANT_MPU9250=y
+CONFIG_WANT_ICM20948=y
+CONFIG_WANT_THERMOCOUPLE=y
+CONFIG_WANT_HX71X=y
+CONFIG_WANT_ADS1220=y
+CONFIG_WANT_LDC1612=y
+CONFIG_WANT_SENSOR_ANGLE=y
+CONFIG_NEED_SENSOR_BULK=y
+CONFIG_WANT_LOAD_CELL_PROBE=y
+CONFIG_NEED_SOS_FILTER=y
+CONFIG_CANSERIAL=y
+CONFIG_CANBUS=y
+CONFIG_CANBUS_FREQUENCY=1000000
+CONFIG_CANBUS_FILTER=y
+CONFIG_INLINE_STEPPER_HACK=y
+CONFIG_HAVE_STEPPER_OPTIMIZED_BOTH_EDGE=y
+CONFIG_WANT_STEPPER_OPTIMIZED_BOTH_EDGE=y
+CONFIG_INITIAL_PINS=""
+CONFIG_HAVE_GPIO=y
+CONFIG_HAVE_GPIO_ADC=y
+CONFIG_HAVE_GPIO_SPI=y
+CONFIG_HAVE_GPIO_I2C=y
+CONFIG_HAVE_GPIO_HARD_PWM=y
+CONFIG_HAVE_STRICT_TIMING=y
+CONFIG_HAVE_CHIPID=y
+CONFIG_HAVE_BOOTLOADER_REQUEST=y
+CONFIG_HAVE_SOFTWARE_DIVIDE_REQUIRED=y

firmware/ebb_rp2240.CAN.old

@@ -0,0 +1,69 @@
+# CONFIG_LOW_LEVEL_OPTIONS is not set
+CONFIG_MACH_AVR=y
+# CONFIG_MACH_ATSAM is not set
+# CONFIG_MACH_ATSAMD is not set
+# CONFIG_MACH_LPC176X is not set
+# CONFIG_MACH_STM32 is not set
+# CONFIG_MACH_HC32F460 is not set
+# CONFIG_MACH_RPXXXX is not set
+# CONFIG_MACH_PRU is not set
+# CONFIG_MACH_AR100 is not set
+# CONFIG_MACH_LINUX is not set
+# CONFIG_MACH_SIMU is not set
+CONFIG_AVR_SELECT=y
+CONFIG_BOARD_DIRECTORY="avr"
+CONFIG_MACH_atmega2560=y
+# CONFIG_MACH_atmega1280 is not set
+# CONFIG_MACH_at90usb1286 is not set
+# CONFIG_MACH_at90usb646 is not set
+# CONFIG_MACH_atmega32u4 is not set
+# CONFIG_MACH_atmega1284p is not set
+# CONFIG_MACH_atmega644p is not set
+# CONFIG_MACH_atmega328p is not set
+# CONFIG_MACH_atmega328 is not set
+# CONFIG_MACH_atmega168 is not set
+CONFIG_MCU="atmega2560"
+CONFIG_AVRDUDE_PROTOCOL="wiring"
+CONFIG_CLOCK_FREQ=16000000
+CONFIG_AVR_CLKPR=-1
+CONFIG_AVR_STACK_SIZE=256
+CONFIG_AVR_WATCHDOG=y
+CONFIG_SERIAL=y
+CONFIG_SERIAL_BAUD_U2X=y
+CONFIG_SERIAL_PORT=0
+CONFIG_SERIAL_BAUD=250000
+CONFIG_USB_VENDOR_ID=0x1d50
+CONFIG_USB_DEVICE_ID=0x614e
+CONFIG_USB_SERIAL_NUMBER="12345"
+CONFIG_WANT_ADC=y
+CONFIG_WANT_SPI=y
+CONFIG_WANT_SOFTWARE_SPI=y
+CONFIG_WANT_I2C=y
+CONFIG_WANT_SOFTWARE_I2C=y
+CONFIG_WANT_HARD_PWM=y
+CONFIG_WANT_BUTTONS=y
+CONFIG_WANT_TMCUART=y
+CONFIG_WANT_NEOPIXEL=y
+CONFIG_WANT_PULSE_COUNTER=y
+CONFIG_WANT_ST7920=y
+CONFIG_WANT_HD44780=y
+CONFIG_WANT_ADXL345=y
+CONFIG_WANT_LIS2DW=y
+CONFIG_WANT_MPU9250=y
+CONFIG_WANT_ICM20948=y
+CONFIG_WANT_THERMOCOUPLE=y
+CONFIG_WANT_HX71X=y
+CONFIG_WANT_ADS1220=y
+CONFIG_WANT_LDC1612=y
+CONFIG_WANT_SENSOR_ANGLE=y
+CONFIG_NEED_SENSOR_BULK=y
+CONFIG_WANT_LOAD_CELL_PROBE=y
+CONFIG_NEED_SOS_FILTER=y
+CONFIG_CANBUS_FREQUENCY=1000000
+CONFIG_INLINE_STEPPER_HACK=y
+CONFIG_HAVE_GPIO=y
+CONFIG_HAVE_GPIO_ADC=y
+CONFIG_HAVE_GPIO_SPI=y
+CONFIG_HAVE_GPIO_I2C=y
+CONFIG_HAVE_GPIO_HARD_PWM=y
+CONFIG_HAVE_STRICT_TIMING=y

firmware/update_fw.sh

@@ -11,8 +11,8 @@
 #rp_sb2209=350f10596216
 #sht36_v2=8ce295109ef0
 
-toolhead_name=rp_sb2209 
+toolhead_name=ebb_rp2240
-toolhead_uuid=350f10596216
+toolhead_uuid=d7e70bd38059
 mcu_uuid=afcf80281237
 mcu_path=/dev/serial/by-id/usb-katapult_stm32h723xx_320006001751313431393536-if00
 config_path=/home/biqu/printer_data/config/firmware/

macros/main.cfg

@@ -26,7 +26,6 @@ initial_duration: 1
 gcode: 
   STATUS_READY
   SET_FAN_SPEED FAN=SoC SPEED=0.3
-  #SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=0
 
 [delayed_gcode _INIT_TIMELAPSE_CHECK_TIME]
 initial_duration: 1
@@ -106,21 +105,7 @@ gcode:
     G28 Z
     G0 Z10 F3600
     STATUS_READY    
-    M117
+    M117  
-    
-[gcode_macro SFS_ENABLE] 
-description: Enable smart filament sensor
-gcode:
-    M117 ENABLING the Smart Filament Sensor
-    G92 E0
-    #SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=1 
-
-[gcode_macro SFS_DISABLE] 
-description: Disable smart filament sensor 
-gcode:
-    M117 DISABLING the Smart Filament Sensor
-    G92 E0
-    #SET_FILAMENT_SENSOR SENSOR=SFS_T0 ENABLE=0
 
 [gcode_macro PRINT_START]
 gcode:
@@ -129,7 +114,7 @@ gcode:
     {% set BED_TEMP = params.BED|default(60)|float %}
     {% set EXTRUDER_TEMP = params.EXTRUDER|default(210)|float %}
     {% set CHAMBER = params.CHAMBER|default(35)|float %}    
-    {% set USE_PURGE = params.PURGE|default(0)|int %}
+    {% set use_purge = params.PURGE|default(0)|int %}
     {% if params.BED_TYPE %}
       INIT_BED_TYPE BED_TYPE="{params.BED_TYPE}"
     {% endif %}
@@ -155,14 +140,13 @@ gcode:
     Smart_Park    
     M117 Heating...
     #M190 S{BED_TEMP}    
-    M109 S{EXTRUDER_TEMP}               ; M109 heat and wait for it to reach temp
+    M109 S{EXTRUDER_TEMP}               ; M109 heat and wait for it to reach temp  
-    SFS_ENABLE
     {% if BED_TEMP > 100 %}
       _NEVERMORE_ON
     {% endif %}
     M117   
     STATUS_CLEANING
-    {% if USE_PURGE == true %}
+    {% if use_purge %}
       VORON_PURGE
     {% endif %}    
     STATUS_PRINTING
@@ -173,8 +157,22 @@ gcode:
     
 
 [gcode_macro PRINT_END]
-#   Use PRINT_END for the slicer ending script - please customise for your slicer of choice
+gcode:
-variable_retract_amount: 16 #
+    {% set use_park = params.PARK|default(1)|int %}   
+    {% if use_park %}
+      PRINT_END_PARK
+    {% endif %}
+    TURN_OFF_HEATERS
+    M107                           ; turn off fan
+    _NEVERMORE_OFF
+    SET_STEPPER_ENABLE STEPPER=extruder ENABLE=0 #disable stepper
+    STATUS_OFF    
+    INIT_BED_TYPE BED_TYPE="None"    
+    M400    
+    TIMELAPSE_TAKE_FRAME
+
+[gcode_macro PRINT_END_PARK]
+variable_retract_amount: 18 #
 variable_park_speed: 6000 #3600
 variable_park_xy: [350,350]
 variable_up_z: 4 #12
@@ -184,24 +182,13 @@ gcode:
     SET_SKEW CLEAR=1
     M400                           ; wait for buffer to clear
     G92 E0                         ; zero the extruder
-    G1 E-{retract_amount} F3600     ; retract filament {max_velocity}
+    G1 E-{retract_amount} F{max_velocity} ;3600     ; retract filament {max_velocity}
     G91                            ; relative positioning
     G0 Z1.00 X20.0 Y20.0 F20000    ; move nozzle to remove stringing
-    TURN_OFF_HEATERS
-    M107                           ; turn off fan
     G1 Z{up_z} F3000                    ; move nozzle up 2mm
     G90                            ; absolute positioning
     G0 X{park_xy[0]} Y{park_xy[1]} F{park_speed}            ; park nozzle at rear
-    #BED_MESH_CLEAR
-    SFS_DISABLE
-    _NEVERMORE_OFF
-    #M141 S35
-    SET_STEPPER_ENABLE STEPPER=extruder ENABLE=0 #disable stepper
-    STATUS_OFF    
     SET_VELOCITY_DEFAULT
-    INIT_BED_TYPE BED_TYPE="None"    
-    M400    
-    TIMELAPSE_TAKE_FRAME
     
 
 
@@ -256,9 +243,7 @@ gcode:
     
     {% if printer['pause_resume'].is_paused|int == 0 %}     
         SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=zhop VALUE={z}                              ; set z hop variable for reference in resume macro
-        SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=etemp VALUE={printer['extruder'].target}    ; set hotend temp variable for reference in resume macro
+        SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=etemp VALUE={printer['extruder'].target}    ; set hotend temp variable for reference in resume macro                                      
-                                
-        SFS_DISABLE                                  ; disable filament sensor       
         SAVE_GCODE_STATE NAME=PAUSE                                                          ; save current print position for resume                
         BASE_PAUSE                                                                           ; pause print
         {% if (printer.gcode_move.position.z + z) < printer.toolhead.axis_maximum.z %}       ; check that zhop doesn't exceed z max
@@ -284,7 +269,6 @@ gcode:
     {% set e = params.E|default(2.5)|int %}
     
     {% if printer['pause_resume'].is_paused|int == 1 %}
-        SFS_ENABLE                          ; enable filament sensor
         #RESETRGB                                                                    ; reset LCD color
         SET_IDLE_TIMEOUT TIMEOUT={printer.configfile.settings.idle_timeout.timeout}  ; set timeout back to configured value
         {% if etemp > 0 %}

mmu/base/mmu_hardware.cfg

@@ -119,8 +119,8 @@ homing_extruder: 1			# CAUTION: Normally this should be 1. 0 will disable the ho
 uart_pin: mmu:MMU_GEAR_UART
 run_current: 1			#
 hold_current: 0.4			# Recommend to be small if not using "touch" or move (TMC stallguard)
-interpolate: True
+interpolate: False
-#sense_resistor: 0.110			# Usually 0.11, 0.15 for BTT TMC2226
+sense_resistor: 0.110			# Usually 0.11, 0.15 for BTT TMC2226
 stealthchop_threshold: 0		# Spreadcycle has more torque and better at speed
 #
 # Uncomment two lines below if you have TMC and want the ability to use filament "touch" homing with gear stepper
@@ -128,16 +128,16 @@ stealthchop_threshold: 0		# Spreadcycle has more torque and better at speed
 #driver_SGTHRS: 60			# 255 is most sensitive value, 0 is least sensitive
 
 
-#[motor_constants 17he12-1204s]
+[motor_constants 17he12-1204s]
-#resistance: 2.5
+resistance: 2.5
-#inductance: 0.0033
+inductance: 0.0033
-#holding_torque: 0.26
+holding_torque: 0.26
-#max_current: 1.20
+max_current: 1.20
-#steps_per_revolution: 200
+steps_per_revolution: 200
 
-#[autotune_tmc stepper_mmu_gear]
+[autotune_tmc stepper_mmu_gear]
-#motor: 17he12-1204s
+motor: 17he12-1204s
-#tuning_goal: performance
+tuning_goal: performance
 
 
 
@@ -281,8 +281,8 @@ sync_feedback_tension_pin:
 sync_feedback_compression_pin: 
 
 # These sensors are on the toolhead and often controlled by the main printer mcu
-extruder_switch_pin: ^!EBBCan:gpio22
+extruder_switch_pin: ^EBBCan:gpio24
-toolhead_switch_pin: 
+toolhead_switch_pin: ^EBBCan:gpio22
 
 
 # ENCODER -------------------------------------------------------------------------------------------------------------
@@ -406,8 +406,8 @@ color_order: GRB		# Set based on your particular neopixel specification (can be
 #
 # (comment out this whole section if you don't have/want leds; uncomment/edit LEDs fitted on your MMU)
 [mmu_leds]
-exit_leds:   neopixel:mmu_leds (8-1)
+exit_leds:   neopixel:mmu_leds (9-16)
-entry_leds:  neopixel:mmu_leds (9-16)
+entry_leds:  neopixel:mmu_leds (8-1)
 #status_leds: neopixel:mmu_leds (17)
 #logo_leds:   neopixel:mmu_leds (18)
 frame_rate: 24

mmu/base/mmu_macro_vars.cfg

@@ -86,7 +86,7 @@ variable_load_initial_tool                  : True	; True/False, Whether to auto
 variable_automap_strategy                   : "none"	; none|filament_name|material|color|closest_color|spool_id
 
 # These variables control the behavior of the MMU_END macro
-variable_user_print_end_extension           : ''	; Executed at start of MMU_END. Good place to move off print
+variable_user_print_end_extension           : 'PRINT_END_PARK'	; Executed at start of MMU_END. Good place to move off print
 variable_unload_tool                        : True	; True/False, Whether to unload the tool at the end of the print
 variable_reset_ttg                          : False	; True/False, Whether reset TTG map at end of print
 variable_dump_stats                         : True	; True/False, Whether to display print stats at end of print

mmu/base/mmu_parameters.cfg

@@ -30,7 +30,7 @@ happy_hare_version: 3.2			# Don't mess, used for upgrade detection
 #
 # Define the physical limits of your MMU. These settings will be respected regardless of individual speed settings.
 #
-gear_max_velocity: 300			# Never to be exceeded gear velocity regardless of specific parameters
+gear_max_velocity: 125 #300			# Never to be exceeded gear velocity regardless of specific parameters
 gear_max_accel: 1500			# Never to be exceeded gear acceleration regardless of specific parameters
 selector_max_velocity: 250		# Never to be exceeded selector velocity regardless of specific parameters
 selector_max_accel: 1200		# Never to be exceeded selector acceleration regardless of specific parameters
@@ -184,7 +184,7 @@ gate_final_eject_distance: 0		# Distance to eject filament on MMU_EJECT (Ignored
 # reading and make correction moves to bring the filament to within the 'bowden_allowable_load_delta' of the end of
 # bowden position (this does require a reliable encoder and is not recommended for very high speed loading >350mm/s)
 #
-bowden_apply_correction: 0		# 1 to enable, 0 disabled. Requires Encoder
+bowden_apply_correction: 1		# 1 to enable, 0 disabled. Requires Encoder
 bowden_allowable_load_delta: 20.0	# How close in mm the correction moves will attempt to get to target. Requires Encoder
 
 # This test verifies the filament is free of extruder before the fast bowden movement to reduce possibility of grinding filament
@@ -269,15 +269,19 @@ toolhead_homing_max: 40			# Maximum distance to advance in order to attempt to h
 # NOTE: If you have a toolhead sensor you can automate the calculation of these parameters! Read about the
 # `MMU_CALIBRATE_TOOLHEAD` command (https://github.com/moggieuk/Happy-Hare/wiki/Blobbing-and-Stringing#---calibrating-toolhead)
 #
-toolhead_extruder_to_nozzle: 99.38		# Distance from extruder gears (entrance) to nozzle
+#toolhead_extruder_to_nozzle: 99.38		# Distance from extruder gears (entrance) to nozzle
-toolhead_sensor_to_nozzle: 	79.78	# Distance from toolhead sensor to nozzle (ignored if not fitted)
+#toolhead_sensor_to_nozzle: 	79.78	# Distance from toolhead sensor to nozzle (ignored if not fitted)
-toolhead_entry_to_extruder: 13.29		# Distance from extruder "entry" sensor to extruder gears (ignored if not fitted)
+#toolhead_entry_to_extruder: 13.29		# Distance from extruder "entry" sensor to extruder gears (ignored if not fitted)
+
+toolhead_extruder_to_nozzle: 101.3 # (currently: 100.9)
+toolhead_sensor_to_nozzle: 88.2 #(currently: 87.4)
+toolhead_entry_to_extruder: 19.1 #(currently: 18.7)
 
 # This setting represents how much residual filament is left behind in the nozzle when filament is removed, it is thus
 # used to reduce the extruder loading length and prevent excessive blobbing but also in the calculation of purge volume.
 # Note that this value can also be measured with the `MMU_CALIBRATE_TOOLHEAD` procedure
 #
-toolhead_residual_filament: 20		# Reduction in extruder loading length because of residual filament left behind
+toolhead_residual_filament: 0		# Reduction in extruder loading length because of residual filament left behind
 
 # TUNING: Finally, this is the last resort tuning value to fix blobbing. It is expected that this value is NEAR ZERO as
 # it represents a further reduction in extruder load length to fix blobbing. If using a wipetower and you experience blobs
@@ -552,7 +556,7 @@ extruder_temp_variance: 2	# When waiting for extruder temperature this is the +/
 #            rotation_distance (MMU_CALIBRATE_GATE) is tuned for other gates.
 #
 autotune_bowden_length: 0       # Automated bowden length calibration/tuning. 1=automatic, 0=manual/off
-autotune_rotation_distance: 0   # Automated gate calibration/tuning (requires encoder). 1=automatic, 0=manual/off
+autotune_rotation_distance: 1   # Automated gate calibration/tuning (requires encoder). 1=automatic, 0=manual/off
 #
 # Other workflow options
 #

mmu/mmu_vars.cfg

@@ -1,36 +1,36 @@
 [Variables]
-mmu__revision = 943
+mmu__revision = 2859
 mmu_calibration_bowden_home = 'encoder'
-mmu_calibration_bowden_lengths = [1785.0, 1785.0, 1785.0, 1785.0, 1785.0, 1785.0, 1785.0, 1785.0]
+mmu_calibration_bowden_lengths = [951.6, 951.6, 951.6, 951.6, 951.6, 951.6, 951.6, 951.6]
-mmu_calibration_clog_length = 23.7
+mmu_calibration_clog_length = 19.0
-mmu_encoder_resolution = 0.960769
+mmu_encoder_resolution = 0.948992
-mmu_gear_rotation_distances = [22.845345, -1, 23.000827, -1, 23.065147, -1, -1, 22.924328]
+mmu_gear_rotation_distances = [22.845345, -1, 23.000827, -1, 23.065147, 22.682752, -1, 22.754847]
 mmu_selector_bypass = 179.2
 mmu_selector_offsets = [4.0, 27.0, 49.9, 72.9, 95.9, 118.9, 141.8, 164.8]
 mmu_servo_angles = {'down': 145, 'up': 30, 'move': 50}
 mmu_state_enable_endless_spool = 0
-mmu_state_filament_pos = 10
+mmu_state_filament_pos = 0
 mmu_state_filament_remaining = 0
 mmu_state_filament_remaining_color = ''
 mmu_state_gate_color = ['green', 'grey', 'black', '', 'cyan', '', '', '3d3846']
 mmu_state_gate_filament_name = ['', '', '', '', '', '', '', '']
 mmu_state_gate_material = ['ABS', 'ABS', 'ABS', '', 'ABS', '', '', 'PETG']
-mmu_state_gate_selected = 7
+mmu_state_gate_selected = -1
 mmu_state_gate_speed_override = [100, 100, 100, 100, 100, 100, 100, 100]
 mmu_state_gate_spool_id = [-1, -1, -1, -1, -1, -1, -1, -1]
-mmu_state_gate_status = [1, 1, 1, 0, 1, 0, 0, 1]
+mmu_state_gate_status = [0, 0, 0, 0, 0, 0, 2, 1]
 mmu_state_gate_temperature = [200, 200, 200, 200, 200, 200, 200, 200]
-mmu_state_last_tool = 2
+mmu_state_last_tool = 5
-mmu_state_tool_selected = 7
+mmu_state_tool_selected = -1
 mmu_state_tool_to_gate_map = [0, 1, 2, 3, 4, 5, 6, 7]
-mmu_statistics_counters = {'servo_down': {'count': 228, 'limit': 5000, 'warning': 'Inspect servo arm for wear/damage', 'pause': False}, 'mmu_restarts': {'count': 37, 'limit': -1, 'warning': ''}, 'cutter_blade': {'count': 0, 'limit': 3000, 'warning': 'Inspect/replace filament cutting blade', 'pause': False}}
+mmu_statistics_counters = {'servo_down': {'count': 599, 'limit': 5000, 'warning': 'Inspect servo arm for wear/damage', 'pause': False}, 'mmu_restarts': {'count': 93, 'limit': -1, 'warning': ''}, 'cutter_blade': {'count': 0, 'limit': 3000, 'warning': 'Inspect/replace filament cutting blade', 'pause': False}}
-mmu_statistics_gate_0 = {'pauses': 0, 'loads': 6, 'load_distance': 8546.739, 'load_delta': 2816.713, 'unloads': 8, 'unload_distance': 3470.0, 'unload_delta': -31.043, 'load_failures': 3, 'unload_failures': 2, 'quality': 0.8889759309441141}
+mmu_statistics_gate_0 = {'pauses': 0, 'loads': 8, 'load_distance': 11954.651, 'load_delta': 4653.767, 'unloads': 11, 'unload_distance': 5205.0, 'unload_delta': 92.747, 'load_failures': 4, 'unload_failures': 2, 'quality': 0.8198260180834479}
-mmu_statistics_gate_1 = {'pauses': 1, 'loads': 2, 'load_distance': 3363.716, 'load_delta': -30.681, 'unloads': 1, 'unload_distance': 1720.0, 'unload_delta': -15.149, 'load_failures': 1, 'unload_failures': 0, 'quality': 1.0071207044795385}
+mmu_statistics_gate_1 = {'pauses': 2, 'loads': 10, 'load_distance': 15191.968, 'load_delta': 770.824, 'unloads': 11, 'unload_distance': 1720.0, 'unload_delta': -15.149, 'load_failures': 2, 'unload_failures': 0, 'quality': 0.9676574716286735}
-mmu_statistics_gate_2 = {'pauses': 0, 'loads': 4, 'load_distance': 6793.725, 'load_delta': 1828.471, 'unloads': 5, 'unload_distance': 1735.0, 'unload_delta': 2.733, 'load_failures': 2, 'unload_failures': 0, 'quality': 0.9016086335436964}
+mmu_statistics_gate_2 = {'pauses': 2, 'loads': 12, 'load_distance': 20421.388, 'load_delta': 8152.369, 'unloads': 17, 'unload_distance': 12115.0, 'unload_delta': 3336.452, 'load_failures': 9, 'unload_failures': 0, 'quality': 0.9635278810027199}
 mmu_statistics_gate_3 = {'pauses': 0, 'loads': 0, 'load_distance': 0.0, 'load_delta': 0.0, 'unloads': 0, 'unload_distance': 0.0, 'unload_delta': 0.0, 'load_failures': 0, 'unload_failures': 0, 'quality': -1.0}
-mmu_statistics_gate_4 = {'pauses': 0, 'loads': 1, 'load_distance': 1729.275, 'load_delta': 1.813, 'unloads': 2, 'unload_distance': 0.0, 'unload_delta': 0.0, 'load_failures': 0, 'unload_failures': 1, 'quality': 0.9989517366625948}
+mmu_statistics_gate_4 = {'pauses': 1, 'loads': 8, 'load_distance': 13584.429, 'load_delta': 9464.65, 'unloads': 11, 'unload_distance': 3440.0, 'unload_delta': 3139.28, 'load_failures': 7, 'unload_failures': 2, 'quality': 0.7126287603755388}
-mmu_statistics_gate_5 = {'pauses': 0, 'loads': 0, 'load_distance': 0.0, 'load_delta': 0.0, 'unloads': 0, 'unload_distance': 0.0, 'unload_delta': 0.0, 'load_failures': 0, 'unload_failures': 0, 'quality': -1.0}
+mmu_statistics_gate_5 = {'pauses': 0, 'loads': 2, 'load_distance': 2852.423, 'load_delta': 423.003, 'unloads': 4, 'unload_distance': 2704.8, 'unload_delta': 149.164, 'load_failures': 1, 'unload_failures': 1, 'quality': 0.8392536837473988}
-mmu_statistics_gate_6 = {'pauses': 0, 'loads': 0, 'load_distance': 0.0, 'load_delta': 0.0, 'unloads': 0, 'unload_distance': 0.0, 'unload_delta': 0.0, 'load_failures': 0, 'unload_failures': 0, 'quality': -1.0}
+mmu_statistics_gate_6 = {'pauses': 4, 'loads': 3, 'load_distance': 3363.452, 'load_delta': 1694.174, 'unloads': 3, 'unload_distance': 901.6, 'unload_delta': 40.864, 'load_failures': 1, 'unload_failures': 1, 'quality': 0.2490142359175044}
-mmu_statistics_gate_7 = {'pauses': 2, 'loads': 1, 'load_distance': 1697.711, 'load_delta': 132.618, 'unloads': 0, 'unload_distance': 0.0, 'unload_delta': 0.0, 'load_failures': 0, 'unload_failures': 0, 'quality': 0.921884173980515}
+mmu_statistics_gate_7 = {'pauses': 6, 'loads': 11, 'load_distance': 14499.488, 'load_delta': 6469.17, 'unloads': 26, 'unload_distance': 22111.2, 'unload_delta': 6092.289, 'load_failures': 7, 'unload_failures': 5, 'quality': 0.5589421641409617}
-mmu_statistics_swaps = {'pre_load': 4.24, 'purge': 6.41, 'post_load': 8.48, 'load': 500.05, 'pre_unload': 4.85, 'form_tip': 134.27, 'unload': 665.18, 'post_unload': 3.93, 'total': 520.23, 'total_swaps': 7, 'swaps_since_pause': 1, 'swaps_since_pause_record': 3, 'total_pauses': 3, 'pause': 57.49}
+mmu_statistics_swaps = {'pre_load': 16.29, 'purge': 17.61, 'post_load': 27.17, 'load': 1499.55, 'pre_unload': 25.33, 'form_tip': 393.62, 'unload': 2817.46, 'post_unload': 22.04, 'total': 1578.64, 'total_swaps': 20, 'swaps_since_pause': 3, 'swaps_since_pause_record': 4, 'total_pauses': 16, 'pause': 1582.58}
 

octopus_pro_1.1.cfg

@@ -34,7 +34,7 @@ spi_software_sclk_pin: PA5
 spi_software_mosi_pin: PA7
 spi_software_miso_pin: PA6
 diag1_pin: ^!PG6
-driver_SGT: 0 #1-3  # -64 is most sensitive value, 63 is least sensitive
+driver_SGT: 1 #1-3  # -64 is most sensitive value, 63 is least sensitive
 run_current: 1.25 #1.25
 stealthchop_threshold: 0
 #stealthchop_threshold: 999999
@@ -84,7 +84,7 @@ endstop_pin: probe:z_virtual_endstop
 [tmc2209 stepper_z]
 uart_pin: PF2
 interpolate: True
-run_current: 0.8
+run_current: 1
 #sense_resistor: 0.110
 #stealthchop_threshold: 999999
 
@@ -98,7 +98,7 @@ microsteps: 128
 [tmc2209 stepper_z1]
 uart_pin: PE4
 interpolate: True
-run_current: 0.8
+run_current: 1
 #sense_resistor: 0.110
 #stealthchop_threshold: 999999
 
@@ -112,7 +112,7 @@ microsteps: 128
 [tmc2209 stepper_z2]
 uart_pin: PE1
 interpolate: True
-run_current: 0.8
+run_current: 1
 #sense_resistor: 0.110
 #stealthchop_threshold: 999999
 
@@ -126,7 +126,7 @@ microsteps: 128
 [tmc2209 stepper_z3]
 uart_pin: PD3
 interpolate: True 
-run_current: 0.8
+run_current: 1
 #sense_resistor: 0.110
 #stealthchop_threshold: 999999
 

printer.cfg

@@ -4,8 +4,8 @@
 [include hbb.cfg]
 
 # Happy Hare
-[include mmu/base/*.cfg]
+#[include mmu/base/*.cfg]
-[include mmu/optional/client_macros.cfg]
+#[include mmu/optional/client_macros.cfg]
 #[include mmu/addons/blobifier.cfg]
 #[include mmu/addons/mmu_erec_cutter.cfg]
 
@@ -208,26 +208,26 @@ algorithm: bicubic
 #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
 #*#
 #*# [skew_correction default]
-#*# xy_skew = -0.0028242858197175757
+#*# xy_skew = -0.002542020467517966
 #*# xz_skew = 0.0
 #*# yz_skew = 0.0
 #*#
 #*# [bed_mesh default]
 #*# version = 1
 #*# points =
-#*# 	  0.045312, 0.016250, 0.030937
+#*# 	  0.005312, 0.005625, 0.016875
-#*# 	  0.045312, 0.009375, 0.050312
+#*# 	  -0.001250, -0.008125, 0.015312
-#*# 	  0.040937, 0.015312, 0.052187
+#*# 	  0.016250, 0.004687, 0.022812
 #*# x_count = 3
 #*# y_count = 3
 #*# mesh_x_pps = 2
 #*# mesh_y_pps = 2
 #*# algo = lagrange
 #*# tension = 0.2
-#*# min_x = 106.493
+#*# min_x = 132.6
-#*# max_x = 243.853
+#*# max_x = 217.0
-#*# min_y = 119.121
+#*# min_y = 133.25
-#*# max_y = 230.50099999999998
+#*# max_y = 217.07
 #*#
 #*# [probe]
-#*# z_offset = -0.870
+#*# z_offset = -0.850

toolhead_sb.cfg

@@ -3,7 +3,7 @@
 [include rapido_v2.cfg]
 
 [mcu EBBCan]
-canbus_uuid: 350f10596216
+canbus_uuid: d7e70bd38059
 
 [firmware_retraction]
 retract_length: 0.3
@@ -34,15 +34,12 @@ accel_per_hz: 125
 hz_per_sec: 1
 
 [input_shaper]
-#max 4000
+#max 4000 
-#shaper_type_x: 2hump_ei 
-#shaper_freq_x: 74.800
-#shaper_type_y: mzv 
-#shaper_freq_y: 40.200 
 shaper_type_x:mzv 
-shaper_freq_x:51.000 
+shaper_freq_x:53.800
 shaper_type_y:mzv 
-shaper_freq_y:40.200 
+shaper_freq_y:42.400
+
 
 [temperature_sensor SB2209]
 sensor_type: temperature_mcu
@@ -112,13 +109,13 @@ motor: ldo-36sth20-1004ahg-9T
 
 
 
-#[filament_switch_sensor G2E]
+[filament_switch_sensor G2E]
-#pause_on_runout: True
+pause_on_runout: True
-#runout_gcode:
+runout_gcode:
-  #UNLOAD_FILAMENT
+  UNLOAD_FILAMENT
-#insert_gcode:
+insert_gcode:
-  #LOAD_FILAMENT
+  LOAD_FILAMENT
-#switch_pin: ^!EBBCan:gpio22
+switch_pin: ^EBBCan:gpio24
 
 
 #####################################################################
@@ -126,7 +123,7 @@ motor: ldo-36sth20-1004ahg-9T
 #####################################################################
 
 [probe]
-pin: ^!EBBCan:gpio24
+pin: ^!EBBCan:gpio21
 
 #####################################################################
 # 	Fan Control