Mikhail Shahovalov
03bda9c56c
Klipper version: v0.13.0-154-g9346ad19 Moonraker version: v0.9.3-77-gccbfd64 Mainsail version: v2.14.0
228 lines
4.4 KiB
INI
228 lines
4.4 KiB
INI
[mcu]
|
|
canbus_uuid: afcf80281237
|
|
|
|
[temperature_sensor OctopusPro]
|
|
sensor_type: temperature_mcu
|
|
|
|
[temperature_sensor Chamber]
|
|
sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
sensor_pin: PF4
|
|
|
|
[output_pin ps_on]
|
|
pin: PE11
|
|
value: 1
|
|
shutdown_value: 1
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## ldo-42sth48-2004mah
|
|
|
|
## X Stepper on Motor0 (B Motor)
|
|
[stepper_x]
|
|
enable_pin: !PF14
|
|
step_pin: PF13
|
|
dir_pin: PF12
|
|
microsteps: 128
|
|
endstop_pin: tmc5160_stepper_x:virtual_endstop
|
|
|
|
[tmc5160 stepper_x]
|
|
interpolate: True
|
|
cs_pin: PC4
|
|
spi_software_sclk_pin: PA5
|
|
spi_software_mosi_pin: PA7
|
|
spi_software_miso_pin: PA6
|
|
diag1_pin: ^!PG6
|
|
driver_SGT: 1 #1-3 # -64 is most sensitive value, 63 is least sensitive
|
|
run_current: 1.25 #1.25
|
|
stealthchop_threshold: 0
|
|
#stealthchop_threshold: 999999
|
|
|
|
## Y Stepper on Motor2 (A Motor)
|
|
[stepper_y]
|
|
enable_pin: !PG5
|
|
step_pin: PF11
|
|
dir_pin: PG3
|
|
microsteps: 128
|
|
endstop_pin: tmc5160_stepper_y:virtual_endstop
|
|
|
|
[tmc5160 stepper_y]
|
|
interpolate: True
|
|
cs_pin: PC6
|
|
spi_software_sclk_pin: PA5
|
|
spi_software_mosi_pin: PA7
|
|
spi_software_miso_pin: PA6
|
|
diag1_pin: ^!PG10
|
|
driver_SGT: 0 #2-3 #range is -64 to +63
|
|
run_current: 1.25 #1.25
|
|
stealthchop_threshold: 0
|
|
#stealthchop_threshold: 999999
|
|
|
|
|
|
[autotune_tmc stepper_x]
|
|
motor: ldo-42sth48-2004mah
|
|
extra_hysteresis: 4
|
|
sgt: 0
|
|
[autotune_tmc stepper_y]
|
|
motor: ldo-42sth48-2004mah
|
|
extra_hysteresis: 4
|
|
sgt: 0
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left on MOTOR4
|
|
[stepper_z]
|
|
enable_pin: !PG2
|
|
step_pin: PF9
|
|
dir_pin: PF10
|
|
microsteps: 128 #128
|
|
endstop_pin: probe:z_virtual_endstop
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PF2
|
|
interpolate: True
|
|
run_current: 1
|
|
#sense_resistor: 0.110
|
|
#stealthchop_threshold: 999999
|
|
|
|
## Z1 Stepper - Rear Left on Motor5
|
|
[stepper_z1]
|
|
enable_pin: !PF1
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
microsteps: 128
|
|
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PE4
|
|
interpolate: True
|
|
run_current: 1
|
|
#sense_resistor: 0.110
|
|
#stealthchop_threshold: 999999
|
|
|
|
## Z2 Stepper - Rear Right on Motor6
|
|
[stepper_z2]
|
|
enable_pin: !PD4
|
|
step_pin: PE2
|
|
dir_pin: PE3
|
|
microsteps: 128
|
|
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PE1
|
|
interpolate: True
|
|
run_current: 1
|
|
#sense_resistor: 0.110
|
|
#stealthchop_threshold: 999999
|
|
|
|
## Z3 Stepper - Fron Right on Motor7
|
|
[stepper_z3]
|
|
enable_pin: !PE0
|
|
step_pin: PE6
|
|
dir_pin: !PA14
|
|
microsteps: 128
|
|
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PD3
|
|
interpolate: True
|
|
run_current: 1
|
|
#sense_resistor: 0.110
|
|
#stealthchop_threshold: 999999
|
|
|
|
[autotune_tmc stepper_z]
|
|
motor: ldo-42sth48-2004ac
|
|
[autotune_tmc stepper_z1]
|
|
motor: ldo-42sth48-2004ac
|
|
[autotune_tmc stepper_z2]
|
|
motor: ldo-42sth48-2004ac
|
|
[autotune_tmc stepper_z3]
|
|
motor: ldo-42sth48-2004ac
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
[heater_bed]
|
|
heater_pin: PA0
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PF3
|
|
#max_power: 0.6
|
|
|
|
#####################################################################
|
|
# Fans
|
|
#####################################################################
|
|
|
|
[controller_fan stepper_drivers_fan]
|
|
pin: PA8
|
|
stepper: stepper_x, stepper_y
|
|
idle_speed: 0
|
|
fan_speed: 0.6
|
|
|
|
#[heater_fan Nevermore]
|
|
#pin: PE5
|
|
#heater_temp: 90
|
|
#max_power: 1.0
|
|
#kick_start_time: 0.5
|
|
#heater: heater_bed
|
|
#fan_speed: 1
|
|
|
|
[fan_generic Nevermore]
|
|
## Nevermore - FAN5 on Octopus
|
|
## Adjust if you use a different board or a different terminal.
|
|
pin: PE5
|
|
|
|
[fan] #CPAP
|
|
pin: PD15
|
|
max_power: 0.8
|
|
shutdown_speed: 0
|
|
cycle_time: 0.005
|
|
hardware_pwm: False
|
|
kick_start_time: 0.100
|
|
off_below: 0.03
|
|
|
|
#[temperature_fan chamber]
|
|
#pin: PD14
|
|
#max_power: 1.0
|
|
#shutdown_speed: 0.0
|
|
#kick_start_time: 5.0
|
|
#cycle_time:0.01
|
|
#off_below:0.1
|
|
#hardware_pwm: True
|
|
#sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
#sensor_pin: PF4
|
|
#min_temp: 0
|
|
#max_temp: 70
|
|
#target_temp: 40
|
|
#control: watermark
|
|
#gcode_id: C
|
|
|
|
# this is the exhaust fan
|
|
# comment out it if you don't have exhaust fan
|
|
[fan_generic exhaust_fan]
|
|
pin: PD14
|
|
cycle_time: 0.01
|
|
hardware_pwm: false
|
|
|
|
[multi_pin soc_pin]
|
|
pins: PD12, PD13
|
|
|
|
|
|
[fan_generic SoC]
|
|
pin: multi_pin: soc_pin
|
|
max_power: 1
|
|
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
[neopixel chamber_leds]
|
|
pin: PB10
|
|
chain_count: 50 #50
|
|
color_order: GRB
|
|
initial_RED: 1.0
|
|
initial_GREEN: 1.0
|
|
initial_BLUE: 1.0
|
|
initial_WHITE: 0.0
|