mikhail
bfc580ced7
Klipper version: v0.12.0-382-ga18c74be0 Moonraker version: v0.9.3-3-gccfe32f Mainsail version: v2.13.2
228 lines
4.9 KiB
INI
228 lines
4.9 KiB
INI
|
|
[include mainsail.cfg]
|
|
[include timelapse.cfg]
|
|
#[include hbb.cfg]
|
|
|
|
[mcu host]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[temperature_sensor BttPi2]
|
|
sensor_type: temperature_host
|
|
|
|
[include octopus_pro_1.1.cfg]
|
|
[include toolhead_sb.cfg]
|
|
#[include toolhead_sht36v2.cfg]
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 500
|
|
max_accel: 8000 #Max 4000
|
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
[force_move]
|
|
enable_force_move: true
|
|
|
|
[respond]
|
|
default_type: echo
|
|
default_prefix: echo:
|
|
|
|
[exclude_object]
|
|
|
|
[gcode_arcs]
|
|
resolution: 0.1
|
|
|
|
[skew_correction]
|
|
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
## X Stepper on Motor1(B Motor)
|
|
[stepper_x]
|
|
rotation_distance: 40 #39.8
|
|
full_steps_per_rotation:400
|
|
position_min: 0
|
|
position_endstop: 355 #355
|
|
position_max: 355 #355
|
|
homing_speed: 80 #25 #Max 100
|
|
#homing_retract_dist: 10
|
|
homing_retract_dist: 0
|
|
homing_positive_dir: true
|
|
|
|
## Y Stepper on Motor2 (A Motor)
|
|
[stepper_y]
|
|
full_steps_per_rotation:400
|
|
rotation_distance: 40 #39.8
|
|
position_min: 0
|
|
position_endstop: 355
|
|
position_max: 355
|
|
homing_speed: 100 #25 #Max 100
|
|
#homing_retract_dist: 5
|
|
homing_retract_dist: 0
|
|
homing_positive_dir: true
|
|
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## Z0 Stepper - Front Left on MOTOR3_A
|
|
[stepper_z]
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
position_max: 300
|
|
position_min: -20
|
|
homing_speed: 15
|
|
second_homing_speed: 3
|
|
homing_retract_dist: 3
|
|
|
|
[stepper_z1]
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
|
|
[stepper_z2]
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
|
|
[stepper_z3]
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
|
|
|
|
#####################################################################
|
|
# Heater
|
|
#####################################################################
|
|
|
|
[verify_heater heater_bed]
|
|
max_error: 120
|
|
check_gain_time: 60
|
|
hysteresis: 5
|
|
heating_gain: 2
|
|
|
|
[verify_heater extruder]
|
|
#max_error: 120
|
|
check_gain_time: 30
|
|
#hysteresis: 5
|
|
#heating_gain: 2
|
|
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
[heater_bed]
|
|
min_temp: 0
|
|
max_temp: 120
|
|
control: pid
|
|
pid_kp: 55.796
|
|
pid_ki: 2.797
|
|
pid_kd: 278.281
|
|
|
|
|
|
#####################################################################
|
|
# Probe
|
|
#####################################################################
|
|
|
|
[probe]
|
|
x_offset: 0
|
|
y_offset: 0
|
|
#z_offset: -0.890
|
|
lift_speed: 15 #10
|
|
speed: 3.0 #5
|
|
samples: 3
|
|
samples_result: median
|
|
sample_retract_dist: 3
|
|
samples_tolerance: 0.005
|
|
samples_tolerance_retries: 6
|
|
activate_gcode:
|
|
{% set PROBE_TEMP = 150 %}
|
|
{% set MAX_TEMP = PROBE_TEMP + 5 %}
|
|
{% set ACTUAL_TEMP = printer.extruder.temperature %}
|
|
{% set TARGET_TEMP = printer.extruder.target %}
|
|
|
|
{% if TARGET_TEMP > PROBE_TEMP %}
|
|
{ action_respond_info('Extruder temperature target of %.1fC is too high, lowering to %.1fC' % (TARGET_TEMP, PROBE_TEMP)) }
|
|
M109 S{ PROBE_TEMP }
|
|
{% else %}
|
|
# Temperature target is already low enough, but nozzle may still be too hot.
|
|
{% if ACTUAL_TEMP > MAX_TEMP %}
|
|
{ action_respond_info('Extruder temperature %.1fC is still too high, waiting until below %.1fC' % (ACTUAL_TEMP, MAX_TEMP)) }
|
|
TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={ MAX_TEMP }
|
|
{% endif %}
|
|
{% endif %}
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
gcode:
|
|
#_CHAMBER_LED_OFF
|
|
|
|
[quad_gantry_level]
|
|
gantry_corners:
|
|
-60,10
|
|
410,420
|
|
points:
|
|
#50,50
|
|
#50,300
|
|
#300,300
|
|
#300,50
|
|
50,50
|
|
50,300
|
|
300,300
|
|
300,50
|
|
speed: 500
|
|
horizontal_move_z: 6
|
|
retries: 10
|
|
retry_tolerance: 0.0075
|
|
max_adjust: 15
|
|
|
|
[bed_mesh]
|
|
speed: 450
|
|
horizontal_move_z: 5
|
|
#mesh_min: 40, 40
|
|
#mesh_max: 310,310
|
|
mesh_min: 35, 30
|
|
mesh_max: 316,308
|
|
fade_start: 0.6
|
|
fade_end: 10.0
|
|
probe_count: 5,5 # Values should be odd, so one point is directly at bed center
|
|
algorithm: bicubic
|
|
#relative_reference_index: 12 #40 #12 # Update when changing probe_count, to ((x points * y points) - 1) / 2. (the center point)
|
|
|
|
|
|
[include macros/main.cfg]
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [skew_correction default]
|
|
#*# xy_skew = -0.0028242858197175757
|
|
#*# xz_skew = 0.0
|
|
#*# yz_skew = 0.0
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.029687, 0.012812, 0.033125
|
|
#*# 0.026562, -0.003750, 0.035000
|
|
#*# 0.028437, 0.026875, 0.050312
|
|
#*# x_count = 3
|
|
#*# y_count = 3
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = lagrange
|
|
#*# tension = 0.2
|
|
#*# min_x = 122.4
|
|
#*# max_x = 227.62
|
|
#*# min_y = 122.26
|
|
#*# max_y = 227.58
|
|
#*#
|
|
#*# [probe]
|
|
#*# z_offset = -0.840
|