[include mainsail.cfg]
[include timelapse.cfg]
#[include hbb.cfg]

[mcu host]
serial: /tmp/klipper_host_mcu

[temperature_sensor BttPi2]
sensor_type: temperature_host

[include octopus_pro_1.1.cfg]
[include toolhead_sb.cfg]
#[include toolhead_sht36v2.cfg]

[printer]
kinematics: corexy
max_velocity: 500  
max_accel: 8000   			#Max 4000
max_z_velocity: 15			#Max 15 for 12V TMC Drivers, can increase for 24V
max_z_accel: 350
square_corner_velocity: 5.0

[force_move]
enable_force_move: true

[respond]
default_type: echo
default_prefix: echo:

[exclude_object]

[gcode_arcs]
resolution: 0.1

[skew_correction]


#####################################################################
# 	X/Y Stepper Settings
#####################################################################

## X Stepper on Motor1(B Motor)
[stepper_x]
rotation_distance: 40 #39.8
full_steps_per_rotation:400
position_min: 0 
position_endstop: 355 #355
position_max: 355 #355
homing_speed: 80 #25   #Max 100
#homing_retract_dist: 10
homing_retract_dist: 0
homing_positive_dir: true 

## Y Stepper on Motor2 (A Motor)
[stepper_y]
full_steps_per_rotation:400
rotation_distance: 40 #39.8
position_min: 0
position_endstop: 355
position_max: 355
homing_speed: 100 #25  #Max 100
#homing_retract_dist: 5
homing_retract_dist: 0
homing_positive_dir: true 


#####################################################################
# 	Z Stepper Settings
#####################################################################

## Z0 Stepper - Front Left on MOTOR3_A
[stepper_z]
rotation_distance: 40
gear_ratio: 80:16
position_max: 300
position_min: -20
homing_speed: 15
second_homing_speed: 3
homing_retract_dist: 3

[stepper_z1]
rotation_distance: 40
gear_ratio: 80:16

[stepper_z2]
rotation_distance: 40
gear_ratio: 80:16

[stepper_z3]
rotation_distance: 40
gear_ratio: 80:16


#####################################################################
# 	Heater
#####################################################################

[verify_heater heater_bed]
max_error: 120
check_gain_time: 60
hysteresis: 5
heating_gain: 2

[verify_heater extruder]
#max_error: 120
check_gain_time: 30
#hysteresis: 5
#heating_gain: 2


#####################################################################
# 	Bed Heater
#####################################################################

[heater_bed]
min_temp: 0
max_temp: 120
control: pid
pid_kp: 55.796
pid_ki: 2.797
pid_kd: 278.281


#####################################################################
# 	Probe
#####################################################################

[probe]
x_offset: 0
y_offset: 0
#z_offset: -0.890
lift_speed: 15 #10
speed: 3.0 #5
samples: 3
samples_result: median
sample_retract_dist: 3
samples_tolerance: 0.005
samples_tolerance_retries: 6
activate_gcode:
    {% set PROBE_TEMP = 150 %}
    {% set MAX_TEMP = PROBE_TEMP + 5 %}
    {% set ACTUAL_TEMP = printer.extruder.temperature %}
    {% set TARGET_TEMP = printer.extruder.target %}

    {% if TARGET_TEMP > PROBE_TEMP %}
        { action_respond_info('Extruder temperature target of %.1fC is too high, lowering to %.1fC' % (TARGET_TEMP, PROBE_TEMP)) }
        M109 S{ PROBE_TEMP }
    {% else %}
        # Temperature target is already low enough, but nozzle may still be too hot.
        {% if ACTUAL_TEMP > MAX_TEMP %}
            { action_respond_info('Extruder temperature %.1fC is still too high, waiting until below %.1fC' % (ACTUAL_TEMP, MAX_TEMP)) }
            TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={ MAX_TEMP }
        {% endif %}
    {% endif %}

#####################################################################
# 	Homing and Gantry Adjustment Routines
#####################################################################

[idle_timeout]
timeout: 1800
gcode: 
  #_CHAMBER_LED_OFF

[quad_gantry_level]
gantry_corners:
	-60,10
	410,420
points:
    #50,50
	#50,300
	#300,300
	#300,50
    50,50
    50,300
    300,300
    300,50
speed: 500
horizontal_move_z: 6
retries: 10
retry_tolerance: 0.0075
max_adjust: 15

[bed_mesh]
speed: 450
horizontal_move_z: 5
#mesh_min: 40, 40
#mesh_max: 310,310
mesh_min: 35, 30
mesh_max: 316,308
fade_start: 0.6
fade_end: 10.0
probe_count: 5,5 # Values should be odd, so one point is directly at bed center
algorithm: bicubic
#relative_reference_index: 12 #40 #12 # Update when changing probe_count, to ((x points * y points) - 1) / 2. (the center point)


[include macros/main.cfg]

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [skew_correction default]
#*# xy_skew = -0.002120454472795053
#*# xz_skew = 0.0
#*# yz_skew = 0.0
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  0.079062, 0.033125, 0.010937, 0.040937, 0.090937
#*# 	  0.065312, 0.020312, -0.009375, 0.033437, 0.080000
#*# 	  0.074375, 0.030312, -0.006563, 0.037500, 0.073125
#*# 	  0.070625, 0.029375, 0.004687, 0.035625, 0.075312
#*# x_count = 5
#*# y_count = 4
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = lagrange
#*# tension = 0.2
#*# min_x = 41.8801
#*# max_x = 308.2001
#*# min_y = 98.38499999999999
#*# max_y = 252.19500000000002
#*#
#*# [probe]
#*# z_offset = -0.840