# SB RapidoV2 G2E [include rapido_v2.cfg] [mcu EBBCan] canbus_uuid: 350f10596216 [firmware_retraction] retract_length: 0.3 # The length of filament (in mm) to retract when G10 is activated, # and to unretract when G11 is activated (but see # unretract_extra_length below). The default is 0 mm. retract_speed: 35 # The speed of retraction, in mm/s. The default is 20 mm/s. #unretract_extra_length: 0 # The length (in mm) of *additional* filament to add when # unretracting. unretract_speed: 35 # The speed of unretraction, in mm/s. The default is 10 mm/s. [adxl345] cs_pin: EBBCan:gpio1 spi_software_sclk_pin: EBBCan:gpio2 spi_software_mosi_pin: EBBCan:gpio0 spi_software_miso_pin: EBBCan:gpio3 axes_map: z,-y,x [resonance_tester] probe_points: 177.5, 177.5, 50 accel_chip: adxl345 min_freq: 15 max_freq: 120 accel_per_hz: 125 hz_per_sec: 1 [input_shaper] #shaper_type_x: mzv #shaper_freq_x: 51 #shaper_type_y: mzv #shaper_freq_y: 41.6 #max 4000 shaper_type_x: 2hump_ei shaper_freq_x: 74.800 shaper_type_y: mzv shaper_freq_y: 40.200 [temperature_sensor SB2209] sensor_type: temperature_mcu sensor_mcu: EBBCan [temperature_sensor Ebb] sensor_type: Generic 3950 sensor_pin: EBBCan:gpio28 ##################################################################### # Extruder ##################################################################### [extruder] step_pin: EBBCan:gpio18 dir_pin: EBBCan:gpio19 enable_pin: !EBBCan:gpio17 microsteps: 16 rotation_distance: 46.64 #G2E gear_ratio: 9:1 #G2E full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: EBBCan:gpio7 #sensor_type: ATC Semitec 104NT-4-R025H42G #sensor_pin: EBBCan:gpio27 #sensor_type: PT1000 #sensor_pin: EBBCan:gpio27 #pullup_resistor: 1000 sensor_type: MAX31865 sensor_pin: EBBCan:gpio9 spi_software_sclk_pin: EBBCan:gpio10 spi_software_mosi_pin: EBBCan:gpio8 spi_software_miso_pin: EBBCan:gpio11 rtd_nominal_r: 1000 rtd_reference_r: 4300 rtd_num_of_wires: 2 min_temp: 20 max_temp: 350 max_power: 1.0 max_extrude_only_distance: 300 max_extrude_cross_section: 5 min_extrude_temp: 20 control: pid pid_Kp: 26.171 pid_Ki: 2.684 pid_Kd: 63.793 [tmc2209 extruder] uart_pin: EBBCan:gpio20 interpolate: false run_current: 0.65 #0.6 #sense_resistor: 0.110 #stealthchop_threshold: 0 # 999999 [autotune_tmc extruder] motor: ldo-36sth20-1004ahg-9T [filament_switch_sensor G2E] pause_on_runout: True # When set to True, a PAUSE will execute immediately after a runout # is detected. Note that if pause_on_runout is False and the # runout_gcode is omitted then runout detection is disabled. Default # is True. runout_gcode: # A list of G-Code commands to execute after a filament runout is # detected. See docs/Command_Templates.md for G-Code format. If # pause_on_runout is set to True this G-Code will run after the # PAUSE is complete. The default is not to run any G-Code commands. UNLOAD_FILAMENT insert_gcode: # A list of G-Code commands to execute after a filament insert is # detected. See docs/Command_Templates.md for G-Code format. The # default is not to run any G-Code commands, which disables insert # detection. LOAD_FILAMENT #event_delay: 3.0 # The minimum amount of time in seconds to delay between events. # Events triggered during this time period will be silently # ignored. The default is 3 seconds. #pause_delay: 0.5 # The amount of time to delay, in seconds, between the pause command # dispatch and execution of the runout_gcode. It may be useful to # increase this delay if OctoPrint exhibits strange pause behavior. # Default is 0.5 seconds. #debounce_delay: 1 # A period of time in seconds to debounce events prior to running the # switch gcode. The switch must he held in a single state for at least # this long to activate. If the switch is toggled on/off during this delay, # the event is ignored. Default is 0. switch_pin: ^!EBBCan:gpio22 ##################################################################### # Probe ##################################################################### [probe] pin: ^!EBBCan:gpio24 ##################################################################### # Fan Control ##################################################################### [fan] #hardware_pwm: False #pin: EBBCan:gpio13 #gpio15 #off_below: 0.05 #cycle_time: 0.00008 # Время (в секундах), необходимое для запуска вентилятора на полной скорости при первом включении # или увеличении ее более чем на 50% (помогает запустить вентилятор). Значение по умолчанию равно 0,100 секунды. #kick_start_time: 0.150 # Время (в секундах), затрачиваемое на каждый цикл подачи питания на вентилятор с помощью ШИМ. # Рекомендуется, чтобы это значение составляло 10 миллисекунд или более при использовании программного управления ШИМ. # Значение по умолчанию равно 0,010 секунды. #cycle_time: 0.01 #tachometer_pin: EBBCan:gpio12 #tachometer_poll_interval: 0.0005 #0.0005 #tachometer_ppr: 1 [heater_fan hotend_fan] ## Hotend Fan - CNC_FAN1 pin: EBBCan:gpio14 #max_power: 1.0 #kick_start_time: 0.5 heater: extruder ## If you are experiencing back flow, you can reduce fan_speed #fan_speed: 1.0 #[temperature_fan EbbFan] #pin: EBBCan:gpio6 #max_power: 1.0 #shutdown_speed: 0.0 #sensor_type: Generic 3950 #sensor_pin: EBBCan:gpio28 #min_temp: 0 #max_temp: 100 #target_temp: 60.0 #control: watermark ##################################################################### # LED Control ##################################################################### [neopixel sb_leds] pin: EBBCan:gpio16