Init

toolhead_sb.cfg

@@ -0,0 +1,161 @@
+# SB RapidoV2 G2E
+
+[include rapido_v2.cfg]
+
+[mcu EBBCan]
+canbus_uuid: 350f10596216
+
+[firmware_retraction]
+retract_length: 0.4
+#   The length of filament (in mm) to retract when G10 is activated,
+#   and to unretract when G11 is activated (but see
+#   unretract_extra_length below). The default is 0 mm.
+retract_speed: 30
+#   The speed of retraction, in mm/s. The default is 20 mm/s.
+#unretract_extra_length: 0
+#   The length (in mm) of *additional* filament to add when
+#   unretracting.
+unretract_speed: 30
+#   The speed of unretraction, in mm/s. The default is 10 mm/s.
+
+[adxl345]
+cs_pin: EBBCan:gpio1
+spi_software_sclk_pin: EBBCan:gpio2
+spi_software_mosi_pin: EBBCan:gpio0
+spi_software_miso_pin: EBBCan:gpio3
+axes_map: z,-y,x
+
+[resonance_tester]
+probe_points: 177.5, 177.5, 50
+accel_chip: adxl345
+min_freq: 15
+max_freq: 120
+accel_per_hz: 125
+hz_per_sec: 1
+
+[input_shaper]
+shaper_type_x: mzv
+shaper_freq_x: 51
+shaper_type_y: mzv
+shaper_freq_y: 41.6
+
+[temperature_sensor SB2209]
+sensor_type: temperature_mcu
+sensor_mcu: EBBCan
+
+
+#####################################################################
+# 	Extruder
+#####################################################################
+
+[extruder]
+step_pin: EBBCan:gpio18
+dir_pin: EBBCan:gpio19
+enable_pin: !EBBCan:gpio17
+microsteps: 16
+rotation_distance: 46.64 #G2E 
+gear_ratio: 9:1	#G2E
+full_steps_per_rotation: 200	#200 for 1.8 degree, 400 for 0.9 degree
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: EBBCan:gpio7
+
+#sensor_type: ATC Semitec 104NT-4-R025H42G
+#sensor_pin: EBBCan:gpio27
+
+#sensor_type: PT1000
+#sensor_pin: EBBCan:gpio27
+
+#pullup_resistor: 1000
+
+sensor_type: MAX31865
+sensor_pin: EBBCan:gpio9
+spi_software_sclk_pin: EBBCan:gpio10
+spi_software_mosi_pin: EBBCan:gpio8
+spi_software_miso_pin: EBBCan:gpio11
+rtd_nominal_r: 1000
+rtd_reference_r: 4300
+rtd_num_of_wires: 2
+
+min_temp: 20
+max_temp: 350
+max_power: 1.0
+max_extrude_only_distance: 300
+max_extrude_cross_section: 5
+min_extrude_temp: 20
+
+control: pid
+pid_Kp: 26.171 
+pid_Ki: 2.684 
+pid_Kd: 63.793
+
+
+
+[tmc2209 extruder]
+uart_pin: EBBCan:gpio20
+interpolate: false
+run_current: 0.65 #0.6
+#sense_resistor: 0.110
+#stealthchop_threshold: 0 # 999999
+
+[autotune_tmc extruder]
+motor: ldo-36sth20-1004ahg-9T
+
+#####################################################################
+# 	Probe
+#####################################################################
+
+[probe]
+pin: ^!EBBCan:gpio24
+
+#####################################################################
+# 	Fan Control
+#####################################################################
+
+[fan]
+hardware_pwm: True
+off_below: 0.05
+# Время (в секундах), необходимое для запуска вентилятора на полной скорости при первом включении 
+# или увеличении ее более чем на 50% (помогает запустить вентилятор). Значение по умолчанию равно 0,100 секунды.
+#kick_start_time: 0.200
+#kick_start_time: 0.5 
+# Время (в секундах), затрачиваемое на каждый цикл подачи питания на вентилятор с помощью ШИМ. 
+# Рекомендуется, чтобы это значение составляло 10 миллисекунд или более при использовании программного управления ШИМ. 
+# Значение по умолчанию равно 0,010 секунды.
+#cycle_time: 0.01
+pin: EBBCan:gpio15
+tachometer_pin: EBBCan:gpio12
+tachometer_poll_interval: 0.0005 #0.0005
+#tachometer_ppr: 1
+
+[heater_fan hotend_fan]
+##	Hotend Fan - CNC_FAN1
+pin: EBBCan:gpio14
+#max_power: 1.0
+#kick_start_time: 0.5
+heater: extruder
+##	If you are experiencing back flow, you can reduce fan_speed
+#fan_speed: 1.0
+
+[temperature_fan EbbFan]
+pin: EBBCan:gpio6
+max_power: 1.0
+shutdown_speed: 0.0
+#kick_start_time: 5.0
+#cycle_time:0.01
+#off_below:0.1
+sensor_type: Generic 3950
+sensor_pin: EBBCan:gpio28
+min_temp: 0
+max_temp: 100
+target_temp: 60.0
+control: watermark
+#gcode_id: C
+
+
+#####################################################################
+# 	LED Control
+#####################################################################
+
+[neopixel sb_leds]
+pin: EBBCan:gpio16