Init

octopus_pro_1.1.cfg

@@ -0,0 +1,203 @@
+[mcu]
+canbus_uuid: afcf80281237
+
+[temperature_sensor OctopusPro]
+sensor_type: temperature_mcu
+
+[output_pin ps_on]
+pin: PE11
+value: 1
+shutdown_value: 1
+
+#####################################################################
+# 	X/Y Stepper Settings
+#####################################################################
+
+## ldo-42sth48-2004mah
+
+## X Stepper on Motor0 (B Motor)
+[stepper_x]
+enable_pin: !PF14
+step_pin: PF13
+dir_pin: PF12
+microsteps: 128
+endstop_pin: tmc2240_stepper_x:virtual_endstop
+
+[tmc2240 stepper_x]
+interpolate: True
+cs_pin: PC4
+spi_software_sclk_pin: PA5
+spi_software_mosi_pin: PA7
+spi_software_miso_pin: PA6
+diag0_pin: ^!PG6
+driver_SGT: 2 #1-3  # -64 is most sensitive value, 63 is least sensitive
+run_current: 1.25 #1.25
+stealthchop_threshold: 0
+#stealthchop_threshold: 999999
+
+## Y Stepper on Motor2 (A Motor)
+[stepper_y]
+enable_pin: !PG5
+step_pin: PF11
+dir_pin: PG3
+microsteps: 128
+endstop_pin: tmc2240_stepper_y:virtual_endstop
+
+[tmc2240 stepper_y]
+interpolate: True
+cs_pin: PC6
+spi_software_sclk_pin: PA5
+spi_software_mosi_pin: PA7
+spi_software_miso_pin: PA6
+diag0_pin: ^!PG10
+driver_SGT: 2 #2-3 #range is -64 to +63
+run_current: 1.25 #1.25
+stealthchop_threshold: 0
+#stealthchop_threshold: 999999
+
+
+[autotune_tmc stepper_x]
+motor: ldo-42sth48-2004mah
+extra_hysteresis: 4
+sgt: 2
+[autotune_tmc stepper_y]
+motor: ldo-42sth48-2004mah
+extra_hysteresis: 4
+sgt: 2
+
+#####################################################################
+# 	Z Stepper Settings
+#####################################################################
+
+## Z0 Stepper - Front Left on MOTOR4
+[stepper_z]
+enable_pin: !PG2
+step_pin: PF9
+dir_pin: PF10
+microsteps: 128 #128
+endstop_pin: probe:z_virtual_endstop
+
+[tmc2209 stepper_z]
+uart_pin: PF2
+interpolate: True
+run_current: 0.8
+#sense_resistor: 0.110
+#stealthchop_threshold: 999999
+
+##	Z1 Stepper - Rear Left on Motor5
+[stepper_z1]
+enable_pin: !PF1
+step_pin: PC13
+dir_pin: !PF0
+microsteps: 128
+
+[tmc2209 stepper_z1]
+uart_pin: PE4
+interpolate: True
+run_current: 0.8
+#sense_resistor: 0.110
+#stealthchop_threshold: 999999
+
+##	Z2 Stepper - Rear Right on Motor6
+[stepper_z2]
+enable_pin: !PD4
+step_pin: PE2
+dir_pin: PE3
+microsteps: 128
+
+[tmc2209 stepper_z2]
+uart_pin: PE1
+interpolate: True
+run_current: 0.8
+#sense_resistor: 0.110
+#stealthchop_threshold: 999999
+
+##	Z3 Stepper - Fron Right on Motor7
+[stepper_z3]
+enable_pin: !PE0 
+step_pin: PE6
+dir_pin: !PA14
+microsteps: 128
+
+[tmc2209 stepper_z3]
+uart_pin: PD3
+interpolate: True 
+run_current: 0.8
+#sense_resistor: 0.110
+#stealthchop_threshold: 999999
+
+[autotune_tmc stepper_z]
+motor: ldo-42sth48-2004ac
+[autotune_tmc stepper_z1]
+motor: ldo-42sth48-2004ac
+[autotune_tmc stepper_z2]
+motor: ldo-42sth48-2004ac
+[autotune_tmc stepper_z3]
+motor: ldo-42sth48-2004ac
+
+#####################################################################
+# 	Bed Heater
+#####################################################################
+
+[heater_bed]
+heater_pin: PA0
+sensor_type: Generic 3950
+sensor_pin: PF3
+#max_power: 0.6
+
+#####################################################################
+# 	Fans
+#####################################################################
+
+[controller_fan stepper_drivers_fan]
+pin: PA8
+stepper: stepper_x, stepper_y
+idle_speed: 0
+fan_speed: 0.6
+
+[heater_fan Nevermore]
+pin: PE5
+heater_temp: 90
+max_power: 1.0
+kick_start_time: 0.5
+heater: heater_bed
+fan_speed: 1
+
+[temperature_fan chamber]
+pin: PD14
+max_power: 1.0
+shutdown_speed: 0.0
+kick_start_time: 5.0
+cycle_time:0.01
+off_below:0.1
+hardware_pwm: True
+sensor_type: ATC Semitec 104NT-4-R025H42G
+sensor_pin: PF4
+min_temp: 0
+max_temp: 70
+target_temp: 40
+control: watermark
+gcode_id: C
+
+
+[multi_pin soc_pin]
+pins: PD12, PD13
+
+
+[fan_generic SoC]
+pin: multi_pin: soc_pin
+max_power: 1
+
+
+#####################################################################
+# 	LED Control
+#####################################################################
+
+[neopixel chamber_leds]
+pin: PB10 
+chain_count: 50 #50
+color_order: GRB
+initial_RED: 1.0
+initial_GREEN: 1.0
+initial_BLUE: 1.0
+initial_WHITE: 0.0