Init
This commit is contained in:
158
macros/nozzle_scrub.cfg
Normal file
158
macros/nozzle_scrub.cfg
Normal file
@@ -0,0 +1,158 @@
|
||||
[gcode_macro clean_nozzle]
|
||||
variable_location_bucket_rear: True
|
||||
variable_enable_purge: True
|
||||
|
||||
# These parameters define your filament purging. The retract variable is used to retract right after purging to prevent unnecessary
|
||||
# oozing. Some filament are particularly oozy and may continue to ooze out of the nozzle for a second or two after retracting. The
|
||||
# ooze dwell variable makes allowance for this. Update as necessary. If you decided to not enable purge, you can ignore this section.
|
||||
variable_purge_len: 20 ; Amount of filament, in mm, to purge.
|
||||
variable_purge_spd: 150 ; Speed, in mm/min, of the purge.
|
||||
variable_purge_temp_min: 200 ; Minimum nozzle temperature to permit a purge. Otherwise, purge will not occur.
|
||||
variable_purge_ret: 2 ; Retract length, in mm, after purging to prevent slight oozing. Adjust as necessary.
|
||||
variable_ooze_dwell: 4 ; Dwell/wait time, in seconds, after purging and retracting.
|
||||
|
||||
# Adjust this so that your nozzle scrubs within the brush. Currently defaulted to be a lot higher for safety. Be careful not to go too low!
|
||||
variable_brush_top: 0
|
||||
|
||||
# These parameters define your scrubbing, travel speeds, safe z clearance and how many times you want to wipe. Update as necessary. Wipe
|
||||
# direction is randomized based off whether the left or right bucket is randomly selected in the purge & scrubbing routine.
|
||||
variable_clearance_z: 5 ; When traveling, but not cleaning, the clearance along the z-axis between nozzle and brush.
|
||||
variable_wipe_qty: 3 ; Number of complete (A complete wipe: left, right, left OR right, left, right) wipes.
|
||||
variable_prep_spd_xy: 3000 ; Travel (not cleaning) speed along x and y-axis in mm/min.
|
||||
variable_prep_spd_z: 1500 ; Travel (not cleaning) speed along z axis in mm/min.
|
||||
variable_wipe_spd_xy: 5000 ; Nozzle wipe speed in mm/min.
|
||||
|
||||
|
||||
# These parameters define the size of the brush. Update as necessary. A visual reference is provided below. Note that orientation of
|
||||
# parameters remain the same whether bucket is at rear or front.
|
||||
#
|
||||
# ← brush_width →
|
||||
# _________________ ↑
|
||||
# | | ↑ If you chose location_bucket_rear = True, Y position is acquired
|
||||
# brush_start (x) | | brush_depth from your stepper_y position_max. Adjust your brush physically in
|
||||
# |_________________| ↓ Y so that the nozzle scrubs within the brush.
|
||||
# (y) ↓
|
||||
# brush_front
|
||||
# __________________________________________________________
|
||||
# PRINTER FRONT
|
||||
#
|
||||
#
|
||||
variable_brush_start: 75
|
||||
# This value is defaulted from brush location in CAD (rear left). Change if your brush width is different.
|
||||
variable_brush_width: 52
|
||||
|
||||
## These are only used if location_bucket_rear is False. You specify a custom location in y axis for your brush - see diagram above. ##
|
||||
variable_brush_front: 0
|
||||
variable_brush_depth: 2
|
||||
|
||||
|
||||
# These parameters define the size of your purge bucket. Update as necessary. If you decided to not enable purge, you can ignore
|
||||
# this section. A visual reference is provided below. Note that orientation of parameters remain the same whether bucket is at rear
|
||||
# or front.
|
||||
#
|
||||
# bucket_gap
|
||||
# ← ---- →
|
||||
# __________________________________________
|
||||
# | | | |
|
||||
# | | | |
|
||||
# bucket_start (x) | |______| |
|
||||
# | | | |
|
||||
# | | | |
|
||||
# |_________________|. . . |_________________|
|
||||
# ← ------------- → ← ------------- →
|
||||
# bucket_left_width bucket_right_width
|
||||
# _______________________________________________________________________________________
|
||||
# PRINTER FRONT
|
||||
#
|
||||
## For V2.4 350mm build, uncomment below
|
||||
variable_bucket_left_width: 92
|
||||
|
||||
# These values are defaulted from bucket geometry in CAD (rear left location). Change only if you're using a custom bucket.
|
||||
variable_bucket_right_width: 40
|
||||
variable_bucket_gap: 22
|
||||
|
||||
# For V1.8, you may need to measure where your bucket start is and input into bucket_start. Otherwise, a value of 0 is for a default
|
||||
# installation of purge bucket at rear left.
|
||||
variable_bucket_start: 0
|
||||
variable_bucket_pos: 1
|
||||
gcode:
|
||||
STATUS_CLEANING
|
||||
# First, check if the axes are homed.
|
||||
{% if "xyz" in printer.toolhead.homed_axes %}
|
||||
|
||||
## Save the gcode state in this macro instance.
|
||||
SAVE_GCODE_STATE NAME=clean_nozzle
|
||||
|
||||
## Set to absolute positioning.
|
||||
G90
|
||||
|
||||
## Grab max position of Y-axis from config to use in setting a fixed y position for location_bucket_rear = True.
|
||||
{% set Ry = printer.configfile.config["stepper_y"]["position_max"]|float %}
|
||||
|
||||
## Check if user enabled purge option or not.
|
||||
{% if enable_purge %}
|
||||
|
||||
### Randomly select left or right bin for purge. 0 = left, 1 = right
|
||||
SET_GCODE_VARIABLE MACRO=clean_nozzle VARIABLE=bucket_pos VALUE={(range(2) | random)}
|
||||
|
||||
### Raise Z for travel.
|
||||
G1 Z{brush_top + clearance_z} F{prep_spd_z}
|
||||
|
||||
### Check if user chose to use rear location.
|
||||
{% if location_bucket_rear %}
|
||||
G1 Y{Ry} F{prep_spd_xy}
|
||||
{% else %}
|
||||
G1 Y{brush_front + (brush_depth / 2)} F{prep_spd_xy}
|
||||
{% endif %}
|
||||
|
||||
### Position for purge. Randomly selects middle of left or right bucket. It references from the middle of the left bucket.
|
||||
G1 X{bucket_start + (bucket_left_width / (2 - bucket_pos)) + (bucket_pos * bucket_gap) + (bucket_pos * (bucket_right_width / 2))}
|
||||
|
||||
### Perform purge if the temp is up to min temp. If not, it will skip and continue executing rest of macro. Small retract after
|
||||
### purging to minimize any persistent oozing at 5x purge_spd. G4 dwell is in milliseconds, hence * 1000 in formula.
|
||||
{% if printer.extruder.temperature >= purge_temp_min %}
|
||||
M83 ; relative mode
|
||||
G1 E{purge_len} F{purge_spd}
|
||||
G1 E-{purge_ret} F{purge_spd * 5}
|
||||
G4 P{ooze_dwell * 1000}
|
||||
G92 E0 ; reset extruder
|
||||
{% endif %}
|
||||
|
||||
{% endif %}
|
||||
|
||||
## Position for wipe. Either left or right of brush based off bucket_pos to avoid unnecessary travel.
|
||||
G1 Z{brush_top + clearance_z} F{prep_spd_z}
|
||||
G1 X{brush_start + (brush_width * bucket_pos)} F{prep_spd_xy}
|
||||
|
||||
## Check if user chose to use rear location.
|
||||
{% if location_bucket_rear %}
|
||||
G1 Y{Ry}
|
||||
{% else %}
|
||||
G1 Y{brush_front + (brush_depth / 2)}
|
||||
{% endif %}
|
||||
|
||||
## Move nozzle down into brush.
|
||||
G1 Z{brush_top} F{prep_spd_z}
|
||||
|
||||
## Perform wipe. Wipe direction based off bucket_pos for cool random scrubby routine.
|
||||
{% for wipes in range(1, (wipe_qty + 1)) %}
|
||||
G1 X{brush_start + (brush_width * (1 - bucket_pos))} F{wipe_spd_xy}
|
||||
G1 X{brush_start + (brush_width * bucket_pos)} F{wipe_spd_xy}
|
||||
{% endfor %}
|
||||
|
||||
## Clear from area.
|
||||
M117 Cleaned!
|
||||
G1 Z{brush_top + clearance_z} F{prep_spd_z}
|
||||
G1 X{bucket_start + (bucket_left_width / 4)} F{prep_spd_xy} #bugfix for right side mounted buckets
|
||||
|
||||
## Restore the gcode state to how it was before the macro.
|
||||
RESTORE_GCODE_STATE NAME=clean_nozzle
|
||||
|
||||
{% else %}
|
||||
|
||||
## raise error will stop any macros that clean_nozzle is referenced in from proceeding for safety.
|
||||
{ action_raise_error("Please home your axes!") }
|
||||
M117 Please home first!
|
||||
|
||||
{% endif %}
|
||||
STATUS_READY
|
||||
Reference in New Issue
Block a user