Autocommit from 2025-05-17 13:10:21

Klipper version: v0.13.0-114-g841a9ca2

Moonraker version: v0.9.3-74-g1c12414

Mainsail version: v2.14.0

firmware/rp_sb2209.CAN.old

@@ -0,0 +1,70 @@
+CONFIG_LOW_LEVEL_OPTIONS=y
+# CONFIG_MACH_AVR is not set
+# CONFIG_MACH_ATSAM is not set
+# CONFIG_MACH_ATSAMD is not set
+# CONFIG_MACH_LPC176X is not set
+# CONFIG_MACH_STM32 is not set
+# CONFIG_MACH_HC32F460 is not set
+CONFIG_MACH_RPXXXX=y
+# CONFIG_MACH_PRU is not set
+# CONFIG_MACH_AR100 is not set
+# CONFIG_MACH_LINUX is not set
+# CONFIG_MACH_SIMU is not set
+CONFIG_BOARD_DIRECTORY="rp2040"
+CONFIG_MCU="rp2040"
+CONFIG_CLOCK_FREQ=12000000
+CONFIG_FLASH_SIZE=0x200000
+CONFIG_FLASH_BOOT_ADDRESS=0x10000100
+CONFIG_RAM_START=0x20000000
+CONFIG_RAM_SIZE=0x42000
+CONFIG_STACK_SIZE=512
+CONFIG_FLASH_APPLICATION_ADDRESS=0x10004000
+CONFIG_RPXXXX_SELECT=y
+CONFIG_MACH_RP2040=y
+# CONFIG_MACH_RP2350 is not set
+CONFIG_RPXXXX_HAVE_BOOTLOADER=y
+# CONFIG_RPXXXX_FLASH_START_0100 is not set
+CONFIG_RPXXXX_FLASH_START_4000=y
+CONFIG_RP2040_STAGE2_FILE="boot2_w25q080.S"
+CONFIG_RP2040_STAGE2_CLKDIV=2
+# CONFIG_RPXXXX_USB is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_0_1 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_12_13 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_16_17 is not set
+# CONFIG_RPXXXX_SERIAL_UART0_PINS_28_29 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_4_5 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_8_9 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_20_21 is not set
+# CONFIG_RPXXXX_SERIAL_UART1_PINS_24_25 is not set
+CONFIG_RPXXXX_CANBUS=y
+# CONFIG_RPXXXX_USBCANBUS is not set
+CONFIG_RPXXXX_CANBUS_GPIO_RX=4
+CONFIG_RPXXXX_CANBUS_GPIO_TX=5
+CONFIG_USB_VENDOR_ID=0x1d50
+CONFIG_USB_DEVICE_ID=0x614e
+CONFIG_USB_SERIAL_NUMBER="12345"
+CONFIG_WANT_GPIO_BITBANGING=y
+CONFIG_WANT_DISPLAYS=y
+CONFIG_WANT_SENSORS=y
+CONFIG_WANT_LIS2DW=y
+CONFIG_WANT_LDC1612=y
+CONFIG_WANT_HX71X=y
+CONFIG_WANT_ADS1220=y
+CONFIG_WANT_SOFTWARE_I2C=y
+CONFIG_WANT_SOFTWARE_SPI=y
+CONFIG_NEED_SENSOR_BULK=y
+CONFIG_CANSERIAL=y
+CONFIG_CANBUS=y
+CONFIG_CANBUS_FREQUENCY=1000000
+CONFIG_CANBUS_FILTER=y
+CONFIG_INITIAL_PINS="!gpio6"
+CONFIG_HAVE_GPIO=y
+CONFIG_HAVE_GPIO_ADC=y
+CONFIG_HAVE_GPIO_SPI=y
+CONFIG_HAVE_GPIO_I2C=y
+CONFIG_HAVE_GPIO_HARD_PWM=y
+CONFIG_HAVE_STRICT_TIMING=y
+CONFIG_HAVE_CHIPID=y
+CONFIG_HAVE_STEPPER_BOTH_EDGE=y
+CONFIG_HAVE_BOOTLOADER_REQUEST=y
+CONFIG_INLINE_STEPPER_HACK=y